Allen-Bradley ControlLogix 36 Pin Screw Terminal Block 1756-TBCH With Good Price In Stock

Brief introduction of 1756-TBCH

The 1756-TBCH is a removable terminal block for the 1756 I/O modules and it is manufactured by Allen-Bradley. The terminal block is a 36-pin cage with the standard housing. The power dissipation of the module is 6.19 watts and the operating temperature for the device is 0 to 60 degrees Celsius. The 1756-TBCH has a weight of 1 kilogram. The device draws a current of 1.2 Amps at 5 Volts DC and 2.5 mA at 24 Volts DC. The module connects with the I/O module and users should connect no more than 2 wires on a single terminal of the device. Users can connect the 1756-TBCH in any of the ControlLogix chassis and the removable terminal block is required for field side wiring.

The 1756-TBCH  can be used for various applications which include high-speed digital processing to process control. While connecting the modules with wires, it is recommended to use a stranded copper wire which can withstand a temperature of 90 degrees Celsius and with a gauge which is greater than 1.2 millimeters. When making the connections to the terminal block, make sure to follow the instructions for connecting the wires and the block as mentioned in the installation manual of the device by the manufacturer. This is essential to ensure the correct operation of the device and for the safety of the equipment. While inserting the wires and tightening the screws, make sure to tighten them to the specified torque rating to prevent breaking the screw due to excessive pressure.

36 Pin Screw Clamp Block With Standard Housing

Technical Specifications for 1756-TBCH

About 1756-TBCH

The Allen-Bradley 1756-TBCH is a Removable Terminal Block (RTB) for 1756 I/O modules. It is an I/O module accessory and must be ordered separately. The 1756-TBCH provides flexibility in interconnecting 1756 I/O modules and industrial plant wiring. It plugs into the front of an I/O module.

The 1756-TBCH removable terminal block is a 36-pin cage-clamp with standard housing (wiring arm depth of 2.5 mm. sq.). When terminating signal to the RTB, the required Torque is 0.5 Nm screw torque. It is recommended to use a screwdriver with width of 3.2 mm (1/8 in.) Screwdriver width. It has dimensions of 5.51 x 4.41 x 5.71 in. and weighs 0.3 pounds. For wiring, use solid or stranded copper wire rated at 90 deg. Celsius (194 °. Fahrenheit) or greater with a gauge 1.2 mm (3/64 in.) maximum insulation must be used. In case of a single wire connection, the wire size must be 0.33 - 2.1 mm sq. (22 - 14 AWG), and for a double wire connection, the wire size must be 0.33 - 1.3 mm sq. (22 - 16 AWG). On any single terminal, do not wire more than two conductors.

Each ControlLogix I/O module can mount in any ControlLogix chassis and they all require a removable terminal block (RTB) to connect all the field-side wiring. Each I/O module has many applications ranging from high-speed digital processing to process control. In a ControlLogix architecture, input and output status are shared between multiple controllers in the same or different chassis using producer-consumer technology. The 1756-TBCH RTB is intended for use in a clean and dry industrial environment with a 0-60 deg. Celsius operating temperature and a 30g operating Shock.

The 1756-TBCH is a 36-Pin cage clamp Removable Terminal Block (RTB) that is used to provide modular and flexible wiring terminal for Input and Output devices. This RTB is a module component that installs in the front of a ControlLogix I/O module, hidden by the module door cover.

RTBs must be ordered separately. Depending on the module, an appropriate RTB is required however, the 1756-TBCH supports most of 1756 ControlLogix modules.

The idea of RTBs is to allow termination of wires without the need of the actual module. Termination may be made with the RTB alone. Once done, the RTB may be easily attached to the main module. Additionally, RTB saves time during troubleshooting and maintenance especially during module replacement. When replacing a module, the entire RTB is uninstalled from the main module. It is then re-installed to the replacement module without need of re-wiring.

Use wire with sizes 0.33 to 2.1 mm. sq. (22 to 14 AWG) solid or stranded copper wire for single wire connection or 0.33 to 1.3 mm sq. (22 to 16 AWG) solid or stranded copper wire for double wire connection. By using the proper wire size, the module door may be closed, and the terminal is still left with room for troubleshooting space. Do not terminate more than Two (2) conductor wires on the same terminal.

Some modules that may be installed with the RTB includes 1756-IA16I, 1756-IA16IK, 1756-IA32, 1756-IA32K, 1756-IB16D, 1756-IB16DK, 1756-IB16I, 1756-IB16IK, 1756-IB16IF, 1756-IB16IFK, 1756-IB16ISOE, 1756-IB16ISOEK, 1756-IB32, 1756-IB32K, 1756-IF8, 1756-IF8K, 1756-OB16IEF, 1756-OB16IEFK, 1756-OB16IS and many other modules.

if you are intersted in more Allen-Bradley product, Please feel free to contct below contact me :windy@hkxytech.com 

Windy Wang 
HONGKONG XIEYUAN TECH CO., LIMITED  
Add: 7-A16,Caishen Commercial Plaza,Hankou Railway Station,Wuhan,China
Tel: +86-27-8588 3233 | Fax:+86-27-8530 9780 | Mobile/Whatsapp :+86 15972199006 | Skype: windy@hkxytech.com
Mail: windy@hkxytech.com 
Website:  http://www.hkxytech.com/   | GMT/UTC +8