Schneider ATV71HC25N4 Variable Speed Drive ATV71 - 250kW-400HP - 480V - EMC filter-graphic terminal With Good Price In Stock
The ATV71HC25N4 is a Variable speed drive ATV71 - 250kW-400HP - 480V - ... that is manufactured by Schneider Electric. These products are manufactured in France and are designed for Material handling, packaging, and textile machines usage. All of the products come with a 2 year warranty from MRO Electric. We also carry AC Drives from other manufacturers such as Modicon and ABB.
Main specification for ATV71HC25N4| Range of product | Altivar 71 |
|---|
| Product or component type | Variable speed drive |
|---|
| Product specific application | Complex, high-power machines |
|---|
| Component name | ATV71 |
|---|
| motor power kW | 220 kW, 3 phases at 380...480 V
250 kW, 3 phases at 380...480 V |
|---|
| motor power hp | 350 hp, 3 phases at 380...480 V
400 hp, 3 phases at 380...480 V |
|---|
| maximum motor cable length | 100 m shielded cable
200 m unshielded cable |
|---|
| power supply voltage | 380...480 V - 15...10 % |
|---|
| Network number of phases | 3 phases |
|---|
| line current | 320 A for 480 V 3 phases 220 kW / 350 hp
357 A for 480 V 3 phases 250 kW / 400 hp
396 A for 380 V 3 phases 220 kW / 350 hp
444 A for 380 V 3 phases 250 kW / 400 hp |
|---|
| EMC filter | Integrated |
|---|
| Assembly style | With heat sink |
|---|
| Variant | Reinforced version |
|---|
| apparent power | 260.6 kVA at 380 V 3 phases 220 kW / 350 hp
292.2 kVA at 380 V 3 phases 250 kW / 400 hp |
|---|
| prospective line Isc | 50 kA for 3 phases |
|---|
| nominal output current | 427 A at 2.5 kHz 380 V 3 phases 220 kW / 350 hp
427 A at 2.5 kHz 460 V 3 phases 220 kW / 350 hp
481 A at 2.5 kHz 380 V 3 phases 250 kW / 400 hp
481 A at 2.5 kHz 460 V 3 phases 250 kW / 400 hp |
|---|
| maximum transient current | 640 A for 60 s 3 phases 220 kW / 350 hp
704 A for 2 s 3 phases 220 kW / 350 hp
721 A for 60 s 3 phases 250 kW / 400 hp
793 A for 2 s 3 phases 250 kW / 400 hp |
|---|
| Output frequency | 0.1…500 Hz |
|---|
| Nominal switching frequency | 2.5 kHz |
|---|
| switching frequency | 2.5...8 kHz adjustable
2.5...8 kHz with derating factor |
|---|
| Asynchronous motor control profile | Sensorless flux vector control (SFVC) (voltage or current vector)
Flux vector control (FVC) with sensor (current vector)
Voltage/frequency ratio (2 or 5 points)
ENA (Energy adaptation) system for unbalanced loads |
|---|
| type of polarization | No impedance for Modbus |
|---|
Complementary| Product destination | Synchronous motors
Asynchronous motors |
|---|
| power supply voltage limits | 323…528 V |
|---|
| power supply frequency | 50...60 Hz - 5...5 % |
|---|
| power supply frequency limits | 47.5...63 Hz |
|---|
| speed range | 1…100 for asynchronous motor in open-loop mode, without speed feedback
1…1000 for asynchronous motor in closed-loop mode with encoder feedback
1…50 for synchronous motor in open-loop mode, without speed feedback |
|---|
| speed accuracy | +/- 0.01 % of nominal speed in closed-loop mode with encoder feedback 0.2 Tn to Tn
+/- 10 % of nominal slip without speed feedback 0.2 Tn to Tn |
|---|
| torque accuracy | +/- 15 % in open-loop mode, without speed feedback
+/- 5 % in closed-loop mode with encoder feedback |
|---|
| transient overtorque | 170 % of nominal motor torque +/- 10 % for 60 s every 10 minutes
220 % of nominal motor torque +/- 10 % for 2 s |
|---|
| braking torque | <= 150 % with braking or hoist resistor
30 % without braking resistor |
|---|
| Synchronous motor control profile | Vector control without speed feedback |
|---|
| Regulation loop | Adjustable PI regulator |
|---|
| Motor slip compensation | Not available in voltage/frequency ratio (2 or 5 points)
Automatic whatever the load
Adjustable
Suppressable |
|---|
| diagnostic | 1 LED (red) for drive voltage |
|---|
| Output voltage | <= power supply voltage |
|---|
| Insulation | Electrical between power and control |
|---|
| type of cable for mounting in an enclosure | With a NEMA Type1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC
With an IP21 or an IP31 kit: 3 wire(s)IEC cable at 40 °C, copper 70 °C / PVC
Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC
Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR |
|---|
| electrical connection | Terminal, clamping capacity: 2.5 mm², AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)
Terminal, clamping capacity: 4 x 185 mm² (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3)
Terminal, clamping capacity: 4 x 185 mm² (PC/-, PA/+) |
|---|
| tightening torque | 0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)
41 N.m, 360 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3)
41 N.m, 360 lb.in (PC/-, PA/+) |
|---|
| supply | Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 mA, protection type: overload and short-circuit protection
Internal supply: 24 V DC (21…27 V), <200 mA, protection type: overload and short-circuit protection |
|---|
| Analogue input number | 2 |
|---|
| analogue input type | AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + sign
AI2 software-configurable current: 0...20 mA, impedance: 242 Ohm, resolution 11 bits
AI2 software-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 11 bits |
|---|
| input sampling time | 2 ms +/- 0.5 ms (AI1-/Al1+) - analog input(s)
2 ms +/- 0.5 ms (Al2) - analog input(s)
2 ms +/- 0.5 ms (LI1...LI5) - discrete input(s)
2 ms +/- 0.5 ms (LI6)if configured as logic input - discrete input(s) |
|---|
| response time | <= 100 ms in STO (Safe Torque Off)
AO1 2 ms, tolerance +/- 0.5 ms for analog output(s)
R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms for discrete output(s)
R2A, R2B 7 ms, tolerance +/- 0.5 ms for discrete output(s) |
|---|
| absolute accuracy precision | +/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C
+/- 0.6 % (AI2) for a temperature variation 60 °C
+/- 1 % (AO1) for a temperature variation 60 °C |
|---|
| linearity error | +/- 0.15 % of maximum value (AI1-/Al1+, AI2)
+/- 0.2 % (AO1) |
|---|
| Analogue output number | 1 |
|---|
| analogue output type | AO1 software-configurable logic output 10 V 20 mA
AO1 software-configurable current 0...20 mA, impedance: 500 Ohm, resolution 10 bits
AO1 software-configurable voltage 0...10 V DC, impedance: 470 Ohm, resolution 10 bits |
|---|
| Discrete output number | 2 |
|---|
| discrete output type | Configurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cycles
Configurable relay logic: (R2A, R2B) NO - 100000 cycles |
|---|
| minimum switching current | 3 mA at 24 V DC for configurable relay logic |
|---|
| maximum switching current | R1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4
R1, R2: 2 A at 30 V DC inductive load, cos phi = 0.4
R1, R2: 5 A at 250 V AC resistive load, cos phi = 1
R1, R2: 5 A at 30 V DC resistive load, cos phi = 1 |
|---|
| Discrete input number | 7 |
|---|
| discrete input type | LI1...LI5: programmable 24 V DC with level 1 PLC, impedance: 3500 Ohm
LI6: switch-configurable 24 V DC with level 1 PLC, impedance: 3500 Ohm
LI6: switch-configurable PTC probe 0…6, impedance: 1500 Ohm
PWR: safety input 24 V DC, impedance: 1500 Ohm conforming to ISO 13849-1 level d |
|---|
| discrete input logic | Negative logic (sink) (LI1...LI5), > 16 V (state 0), < 10 V (state 1)
Positive logic (source) (LI1...LI5), < 5 V (state 0), > 11 V (state 1)
Negative logic (sink) (LI6)if configured as logic input, > 16 V (state 0), < 10 V (state 1)
Positive logic (source) (LI6)if configured as logic input, < 5 V (state 0), > 11 V (state 1) |
|---|
| Acceleration and deceleration ramps | Automatic adaptation of ramp if braking capacity exceeded, by using resistor
Linear adjustable separately from 0.01 to 9000 s
S, U or customized |
|---|
| Braking to standstill | By DC injection |
|---|
| protection type | Against exceeding limit speed: drive
Against input phase loss: drive
Break on the control circuit: drive
Input phase breaks: drive
Line supply overvoltage: drive
Line supply undervoltage: drive
Overcurrent between output phases and earth: drive
Overheating protection: drive
Overvoltages on the DC bus: drive
Short-circuit between motor phases: drive
Thermal protection: drive
Motor phase break: motor
Power removal: motor
Thermal protection: motor |
|---|
| insulation resistance | > 1 mOhm 500 V DC for 1 minute to earth |
|---|
| frequency resolution | Analog input: 0.024/50 Hz
Display unit: 0.1 Hz |
|---|
| Communication port protocol | CANopen
Modbus |
|---|
| connector type | 1 RJ45 (on front face) for Modbus
1 RJ45 (on terminal) for Modbus
Male SUB-D 9 on RJ45 for CANopen |
|---|
| physical interface | 2-wire RS 485 for Modbus |
|---|
| transmission frame | RTU for Modbus |
|---|
| transmission rate | 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
9600 bps, 19200 bps for Modbus on front face
20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen |
|---|
| data format | 8 bits, 1 stop, even parity for Modbus on front face
8 bits, odd even or no configurable parity for Modbus on terminal |
|---|
| number of addresses | 1…127 for CANopen
1…247 for Modbus |
|---|
| method of access | Slave CANopen |
|---|
| Marking | CE |
|---|
| Operating position | Vertical +/- 10 degree |
|---|
| Height | 1190 mm |
|---|
| Depth | 377 mm |
|---|
| Width | 595 mm |
|---|
| Net weight | 207 kg |
|---|
| Functionality | Full |
|---|
| Specific application | Other applications |
|---|
| option card | Communication card for CC-Link
Controller inside programmable card
Communication card for DeviceNet
Communication card for EtherNet/IP
Communication card for Fipio
I/O extension card
Communication card for Interbus-S
Interface card for encoder
Communication card for Modbus Plus
Communication card for Modbus TCP
Communication card for Modbus/Uni-Telway
Overhead crane card
Communication card for Profibus DP
Communication card for Profibus DP V1 |
|---|
Environment| noise level | 77 dB conforming to 86/188/EEC |
|---|
| dielectric strength | 3535 V DC between earth and power terminals
5092 V DC between control and power terminals |
|---|
| electromagnetic compatibility | 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6
Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4
Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3
Voltage dips and interruptions immunity test conforming to IEC 61000-4-11 |
|---|
| Standards | EN/IEC 61800-5-1
UL Type 1
IEC 60721-3-3 class 3C2
EN 61800-3 environments 1 category C3
EN/IEC 61800-3
EN 55011 class A group 2
EN 61800-3 environments 2 category C3 |
|---|
| Product certifications | NOM 117
GOST
CSA
C-Tick
UL |
|---|
| pollution degree | 2 conforming to EN/IEC 61800-5-1
3 conforming to UL 840 |
|---|
| IP degree of protection | IP20 |
|---|
| vibration resistance | 0.6 gn (f= 10…200 Hz) conforming to EN/IEC 60068-2-6
1.5 mm peak to peak (f= 3…10 Hz) conforming to EN/IEC 60068-2-6 |
|---|
| shock resistance | 4 gn for 11 ms conforming to EN/IEC 60068-2-27 |
|---|
| relative humidity | 5…95 % without condensation conforming to IEC 60068-2-3
5…95 % without dripping water conforming to IEC 60068-2-3 |
|---|
| ambient air temperature for operation | -10…50 °C (without derating) |
|---|
| Ambient air temperature for storage | -25…70 °C |
|---|
| operating altitude | <= 1000 m without derating
1000...3000 m with current derating 1 % per 100 m |
|---|
Packing Units| Unit Type of Package 1 | PCE |
|---|
| Number of Units in Package 1 | 1 |
|---|
| Package 1 Height | 43.0 cm |
|---|
| Package 1 Width | 51.0 cm |
|---|
| Package 1 Length | 122.5 cm |
|---|
| Package 1 Weight | 68.0 kg |
|---|
Contractual warranty| Warranty | 18 months |
|---|
HONGKONG XIEYUAN TECH CO.,LTD, established in 7th Nov.,2012, a comprehensive corporation with its independent rights of export and import.. We are committed to providing customers with convenient and efficient industrial supplies services. From the product, price, logistics, service process for customers to improve procurement efficiency, reduce procurement costs, and grow together with customers.
Xieyuan sales of major brands are: Yokogawa, Siemens, ABB, Schneider, Emerson, Rosemount, Honeywell, Pepper+Fuchs, MTL, Fluke, Fisher, Endress+Hauser, Phoenix Contact, Weidmüller, Triconex, KROHNE, Dräger, Allen-Bradley, Omron, Eaton, SMC, Eaton, RAE, Testo, MSA, FESTO, Vega, Yaskawa, Danfoss, GE, Fisher, Hirschmann, IFM, Turck, MOXA, Foxboro etc.
Our wide range of products include Field Instruments, Field Communicator, Gas Detectors, Process Analyzers, Pressure Transmitters, Temperature Transmitters, Flow Meters, Inverters, Multimeters, Safety Barriers, Positioners, Controllers, Valves, Circuit Breakers, Sensors, DCS, PLC etc.
We endeavor to provide our customer with high quality, 100% original brand new products at competitive prices. Our targeting market includes Oil and Gas Industry, Refinery, Chemical, Mineral, Power and Energy, Ocean Engneering, Electricity, Food, Environment Protection and many other fields.
We operate in more than 50 countries around the world. There are: Singapore, Indonesia, Malaysia, Philippines, Vietnam, Thailand, South Korea, Kazakhstan, Bangladesh, United Arab Emirates, Saudi Arabia, Iran, Iraq, Kuwait, Oman, Qatar,Germany, Italy, Austria, UK, Nigeria, Pakistan, Egypt, USA, Chile, Brazil, Mexico etc.
CHINA MAINLAND ADDRESS:
7-A16,CAISHEN COMMERCIAL PLAZA, HANKOU RAILWAY STATION, WUHAN, CHINA.
All products will send out within 72 hours, Please feel free to contact us! Thanks
Windy Wang
HONGKONG XIEYUAN TECH CO., LIMITED
Add: 7-A16,Caishen Commercial Plaza,Hankou Railway Station,Wuhan,China
Tel: +86-27-8588 3233 | Fax:+86-27-8530 9780 | Mobile/Whatsapp :+86 15972199006 | Skype: windy@hkxytech.com
Mail: windy@hkxytech.com
Website: http://www.hkxytech.com/ | GMT/UTC +8
